top of page
Search

1K or 2K? What the Coating Brands Actually Sell

Nov 7
6 min read

Two letters show up in every kitchen cabinet-coating conversation: 1K and 2K. They are not brands, and they are not a ranking. They describe how a coating hardens — and the difference matters, because it decides what is in the air while the finish is sprayed. This post is the reference version: what each of the major cabinet-coating brands actually sells, in 1K form, in 2K form, or both, taken from the makers' own data sheets and safety sheets. Nothing here goes beyond what those sheets say.


1K means the coating is ready from the can. Nothing is added.


2K means a hardener is mixed in before spraying. Once the hardener is in, the clock starts: the mix has a pot life, and what is left over when the clock runs out is waste. The hardener, in nearly every 2K cabinet coating, is an isocyanate chemical. That last sentence is the one worth checking, brand by brand, because it is where the marketing words and the safety sheets meet.


Crosslinking is a trade word, and it's worth saying plainly. As the finish dries, it locks itself together into one connected skin instead of a layer of dried paint — so it doesn't soften back up under cleaner or water, and it holds instead of chipping. The 1K colour coat crosslinks as it dries; that's built into the coating itself. The 2K route gets there by adding the hardener. Same word, different route — and only the hardener route puts isocyanates in the air.


Breathing protection is where the sheets and the guidance part company, and the difference is worth knowing. Each hardener sheet carries its own respirator wording — Envirolak's hardener sheet, for example, calls for NIOSH-certified organic vapour/particulate respirators where ventilation is insufficient. Ontario's guidance on isocyanates, written for auto body shops, goes further for spraying: a supplied-air respirator, with air through a hose from outside the spray area, while spraying is underway (Ontario's guidance on isocyanates, O. Reg. 490/09: https://www.ontario.ca/page/isocyanates-auto-body-shops). That guidance is guidance — it is written for auto body shops, not a law about spraying in a home. But it is the province's own word on what spraying an isocyanate calls for.


Cleanup is part of the system, too — and it is where the coating in the can meets the drain. A pump-fed airless rig is a pump, a long hose, and a gun, and all three have to be flushed clean.


Water-based coatings flush with water. But wherever isocyanate is in the mix, the flush has to be a solvent that dissolves the mixed material — acetone is the wash solvent Envirolak names for its equipment — and that solvent has to be moisture-free, because isocyanates react with water and leave hard crystals in the lines. Those who use 2K never say where the extra product goes — the mix left over when the pot life runs out, plus the flush solvent. And the flush has to happen where the rig is: a 2K mix keeps curing in the lines, so it cannot wait for a drive back to the shop. That means the flushing happens at the home, inside it or outside it. Graco's flushing procedure calls for a grounded metal waste pail, with the gun held against the pail and the tip removed. And it is not one quick rinse: Graco warns the solvent can channel straight through the mix and leave material coating the inside of the hose, so the flush has to be thorough and repeated.

In Ontario the flush solvent and the leftover mix cannot go down a drain or into the garbage — Windsor's own liquid-waste page says solvents can cause explosive or toxic situations in residential plumbing and sewer systems — they go to a hazardous-waste depot, and a business's quantities go through the commercial route. Here in Windsor-Essex, that depot is the Household Chemical Waste Depot at 3560 North Service Road East in Windsor, run by the Essex-Windsor Solid Waste Authority. Residents drop off up to two 20-litre pails free — anything more counts as commercial and is billed, with the fee set by the load, so a business calls ahead. That cost is part of doing the job properly, and it is built into the price. It is one reason proper work costs more than a quote that says nothing about where the waste goes.


What's left of a water-based coating is a different story: it dries out in the can, and the cans go to the depot two or three times a year. My own setup is simpler: an HVLP gun with a cup — no pump, no long hose. Cleanup is cleaning out a cup. Ask the questions before the job starts: what do you flush with, where do you flush it, and where does the extra product go?

1K and 2K are not brands, and neither one is automatically the right answer. They describe how a coating hardens, and the hardener is the part that decides what is in the air.


Check the product, check the hardener, check the sheet. Our own system is backed by our NEW 5-Year No Peel Warranty.


The brands, one by one.


Gemini — EVO Eclipse is a 1K - 2K Hybrid


Gemini EVO Eclipse, the colour coat in our own system, is sold as a 1K: ready from the can, no hardener needed. Gemini also sells an optional hardener, EVO Hardener EWH5, added at 5 to 10%. Stir it in and EVO becomes a 2K system, with a pot life of one to two hours. EWH5's own safety sheet lists blocked IPDI homopolymer at 15 to 60% and blocked HDI homopolymer at 10 to 30%, plus 0.1 to 1% free IPDI, and carries the signal word Danger and a respiratory sensitizer warning. "Blocked" is worth understanding: the reactive ends are capped so the hardener can sit in water, and the caps come off as the film cures. Blocked is not isocyanate-free. We do not use EWH5.


Milesi — 2K polyurethanes, and 1K waterbornes


Milesi, the Italian maker, sells 2K polyurethane lines — acrylic and aromatic — that take hardeners coded LNB99 (non-yellowing, for acrylics) and LNB77 (aromatic). Milesi's own technical material describes the hardener as a solution of polyisocyanate polymer. Milesi also sells single-component waterborne topcoats, such as the HSC603X series, which need no hardener at all. Same maker, both routes — which is why the brand name alone never answers the question.


Renner — Aquaris, both routes


Renner's Aquaris range includes single-component, two-component, and UV-drying coatings. The 2K kitchen topcoats, such as the 688 series, are catalyzed with hardener YC-M403 or YC-M404 at 10 to 15%. Renner's own catalogue says two-component water-based coatings "need to be mixed with an isocyanate hardener." One exception is worth naming fairly: Renner also makes a hardener without diisocyanates, YC-M410, built on aziridine chemistry — but it belongs to Renner's exterior window and door system, not the kitchen topcoats.


Envirolak — Canadian, both routes


Envirolak is made in Mississauga. Envirocryl 400 is a one-component white topcoat that can also be used as a 2K with 5% CAT100-LV hardener, or crosslinked with a product called CAT150. CAT150 is a different kind of additive from the CAT100-LV hardener: its own safety sheet lists only serious eye irritation, with no respiratory-sensitizer classification — unlike the hardener's sheet. The sheet withholds the active ingredient as a trade secret, so no chemistry is named for it here. Envirothane 800 is a one-component white topcoat. Envirocryl 500 can be catalyzed with CAT100-LV. The hardener's own sheet lists HDI isocyanurate oligomers at 70 to 85% and HDI monomer at 0.1 to 0.3%, and warns that it may cause allergy or asthma symptoms or breathing difficulties if inhaled.


Sherwin-Williams — Gallery Series, 1K only


Sherwin-Williams Gallery Series is a single-component 1K. The company sells it as needing no on-site mixing, with "two-component performance with a one-component system" — its own words. No hardener is offered for Gallery, and the crosslinking is built into the resin. Sherwin-Williams does sell 2K hardeners for other, mostly industrial lines — just not for Gallery.


General Finishes — Enduro 2K


General Finishes Enduro 2K White Poly and 2K Clear Poly are two-component water-based urethanes. They take Enduro NCO Catalyst A152 at 10% by volume, with a pot life of about four hours. The catalyst's own sheet names it an aliphatic polyisocyanate in solution — HDI isocyanurate oligomers at about 45% and IPDI oligomers at about 20% — with the signal word Danger and a possible-sensitizer warning.


One product sits outside this comparison: Varathane Nano Defense, the clear coat on our doors. It is a one-component urethane-acrylic clear, and it is not a colour coat, so it is not ranked here.


How to check any coating


Ask for two names: the product, and the hardener. Then open the hardener's safety data sheet. Section 3 lists what is in it; Section 2 lists the hazards. If Section 3 names a polyisocyanate or a diisocyanate, the system is a 2K isocyanate system. If there is no hardener at all, it is a 1K. The sheet is the maker's own document — it settles the question better than any ad.


Get a free quote from us. Call or text us at (519) 401-3161.

Previously: "Safe and Eco-Friendly"? Ask What's in the Air — and What the Warranty Covershttps://www.sprayitlikenew.kitchen/post/safe-eco-friendly-warranty-questions

The Cast Iron Look for a Kitchen

 
 
 

Comments


Spray It Like New
InfraKure Logo

Kitchen Cabinet Painters Transforming kitchens, bath & laundry cabinets with durable, high quality Water Poly Cross Linking Urethane finishes. With Our NEW 5-Year No Peel Warranty! 

  • Facebook
  • YouTube
  • Instagram
  • Pinterest

Spray Shop Located at:

21028 Four Rod Rd.

Charing Cross

N0P 1G0

contact.quotes@sprayitlikenew.kitchen​

 (519) 401 3161

​

​

​

​

"Spray It Like New" & "InfraKure" are Registered Trademarks of Tracy Sauer | sprayitlikenew.kitchen  © 2011 to 2026

​Gemini Evo Eclipse & Sirca North America are Registered Trade Marks of Gemini Industries,​ Zinnser BIN Shellac Primer is a Registered Trademark of Rustoleum Corporation

bottom of page